Xhorse Multi Prog Read and Write BMW MSV90

 How-to: read and write BMW X3 MSV90 DME using Xhorse Multi Prog programmer on bench.

Read ok, write OK, checksum by multi-prog.

 

Steps:

Reading information from the old computer:

Select ALL from the menu.

Choose IMMOBILIZER.

Read the computer’s serial number.

Select the corresponding option and press OK.

Choose BENCH to read the information without removing the computer.

Follow the schematic to connect the cables.

Click on EEBROM to read the memory.

Click on FLASH to read the file.

Click on OPEN then VERIFY to ensure the file’s integrity.

Click OK to start writing.

Wait until the percentage reaches 100%.

Writing information to the new computer:

Select ALL from the menu.

Choose IMMOBILIZER.

Write the serial number of the new computer.

Select the corresponding option and press OK.

Choose BENCH to write the information without removing the computer.

Follow the schematic to connect the cables.

Click on EEBROM to write the memory.

Click on FLASH to write the file.

Click on OPEN then WRITE to write the file.

Wait until the percentage reaches 100%.

Starting the car:

Connect the new computer to the car. Start the car.

 

Notes:

Make sure to use the Xhorse MULTI BROG software version 1.44 or later. Ensure proper cable connections. Verify file integrity before writing. With these simple steps, you can successfully transfer information from an old BMW computer to a new one.

 

www.vvdishop.com

VVDI Super Chip Ford ID49 Key Not Working Solution?

 Problem:

I have vvdi mini Key tool and I use vvdi super chip XT27A with ID49 selected from ID49 Ford USA (They was malesia as well.. i choose USA) generates successfully but car/van doesnt wanna accept chip under programming immo.

Long time aago when i has XT27B and was available i use that chip and work ok but as you know XT27B stop production.

Do you know if XT27A can be generated correctly to work with ford mazda key chip immobiliser id49 hitag pro 2015+ ?

 

Here is the clue:
You could use an XS smart key and generate the profile for which ford key.

You need and should work also.

You can get the XEB510EN B5 Super Remote with xt27b chip.

Xhorse Multi Prog Read and Write Volvo CEM TB28F400

 In my previous test, Xhorse VVDI PROG does not work with Volvo CEM TB28F400 microcircuits . It can erase them but cannot write. Now I’ve already have the next generation Xhorse Multi-Prog Programmer respectively. And the XDMPO4GL VH24 SOP44 Adapter was purchased specifically for these microcircuits.

 

With the TB28F400 B5B microcircuit was installed, now let’s see a clear difference between the Multi-Prog Programmer& VVDI PROG.

Open MultiProgsoftware,

Click “Read”.

Read success.

In the Device settings, I can select “Verify after reading”. It’s very useful option I strongly recommend it.

 

Open the prepared file.

Click “Write”.

Let’s see if it will be successful, just waiting for the result.

Writing success.

Save the file.

Finally, let’s compare the original file with the new saved file.

They are exactly the same.

The files are identical.

 

Actually, the difference between Multi-Prog & VVDI PROG is already clearly: it works with these microcircuits, not only start recording. Therefore, you need to purchase the appropriate adapter SOP44. Everything will be fine.

Read also:

Xhorse VVDI Prog vs Multi Prog

Xhorse Multi Prog Read Renault Megane 2 UCH

 How to read Renault Megane 2 Scenic 2 UCH immobilizer data using Xhorse Multi Prog?

Quick search ‘uch’ and select Megane UCH

Check wiring diagram

After opening the module case, we take out the motherboard and solder our points according to the wiring diagram in the Multi-Prog tool.

It is worth equipping the yellow wire with a measuring needle. This will make it easier for us to find the right point.

Read eeprom. File size 4kb.

It takes 3s to read eeprom.

Save eeprom.

Read flash.

File size 256kb.

Xhorse Multi-prog read flash in 39 seconds. very fast.

Save flash.

www.vvdishop.com

Xhorse VVDI2 V7.3.6 Adds VAG MLB Key Learning

 Xhorse VVDI2 key programmer released new software version V7.3.6 on March 31st, 2024.

 

*** 2024-03-31
*** Require firmware V7.3.5
************************************************************************
===== VAG V7.3.6 =====
1. Support MLB immobilizer key learning-Require VVDI-MLB TOOL
2. Support Fix dashboard data for MQB48-NEC35xx(Lock) type
3. Support Clone MQB48-NEC35xx(Lock) type dashboard (Copy CS/Component protection data from old data to new data)
4. Support Fix KM for MQB48-RH850 type-Require MultiPROG or KEY TOOL PLUS
5. Bugfix

===== BMW V7.3.6 =====
1. Bugfix

===== Porsche V7.3.6 =====
1. Bugfix

===== PSA V7.3.6 =====
1. Bugfix

===== Transponder Programmer V7.3.6 =====
1. Immobilizer data tool: Asia->China immobox->Simens immobox->93C56 add new type
2. Immobilizer data tool: Asia->Mzada->BT-50->95320 add 8C type
3. Immobilizer data tool: Asia->Honda->Bike(PCX/VARIO) display PIN code
4. Immobilizer data tool: Asia->Ducati->1199 Panigale->9S12 bugfix
5. Bugfix

===== Copy 48 (96 bits) V7.3.6 =====
1. Bugfix

===== J2534 V7.3.6 =====
1. Bugfix

===== Online Upate Tool V7.3.6 =====
1. Bugfix

===== Quick Start V7.3.6 =====
1. Bugfix

 

Free download VVDI2 V7.3.6 software
http://dl.xhorse.com/product/vvdi2/software/VVDI2-InstallerV736.exe

How to Disable Benz FBS4 Key with Xhorse VVDI MB?

 How to disable key Mercedes W203 with xhorse vvdi mb tool?

 

VVDI MB will disable FBS4 key. This function is suitable to disabling the keys of W166, W205, W213, W218, W22, W246 chassis.

Go to Menu->Other function->FBS4 Disable Key

Select the corresponding key position and click Disable key.

www.vvdishop.com

How to Force Xhorse Multi Prog Firmware Update?

  Problem:

Failed to update xhorse multi prog firmware (Jump recovery error). The current firmware is 1.1.0. Also failed to sync device. Any solution?

Solution:

Press and hold the Reset button on the main unit before powering on, and hold it for 5 seconds after powering on. Try to force firmware upgrade.

Program 2010 Ford Transit Mk7 AKL by VVDI Prog and VVDI2

 2010 Ford Transit Mk7 all keys lost and active Cat1 factory alarm.

Key learning cannot be carried out by normal OBD operation with alarm active as key learning by OBD is blocked.

 

Removed BCM, read key data (chip MC9S12DG256) directly from the module using xhorse vvdi prog on the bench, added a new key on the bench with xhorse vvdi2, installed BCM back to the van, switch ignition on with registered key and alarm is deactivated.
Now we can erase all keys and add new all by OBD.

 

Xhorse Clone Volvo ID48 96bit Transponder

 Problem:

When cloning Volvo ID48 96bit transponder online with vvdi key tool plus, it says acquisition data is the same, invalid data and discarded. Any solution?

Solution:

Here are the tips to clone Volvo ID48 96bit transponder with xhorse.

If it is Volvo model, each time can collect 1 set data, require to disconnect power to collect next set data.

www.vvdishop.com